Products

General partner

News

May 2011
infra-red panels TPS and TPS AL were certified. Certificates and CE declarations you can find in „Products“.

The basic product range of infrared panels (earlier product name STROPTERM):

           The heating Ecora panels are made for ceiling heating of flats, apartments, industrial or business spaces. Minimum height is 1,8m from floor in case of hanging panel onto the wall.
           The heating panels consists of built-in heating unit NOMATERM (type 1). NOMATERM unit is covered with silicon sand and white painted in standard design.

           The types and dimensions of the infrared panels Ecora are specified according to technical conditions of built-in NOMATERM unit with its input 10 W/dm² of working area.
         The infrared panel is made for the maximum surface temperature of 100 ^o C.

           Possible maintenance of product is cleaning dusted surface with the vacuum cleaner or wet sponge. Do not use any detergent or dissolution reagent to clean working area of the panel. Panel must be cold and completely disconnected during maintenance. Only producer could make any repairs. All electro operations during installation must be done only by certified electrician.

           Ecora panels are made in different versions by kind of used frame :

1) Type TPS ( Ecora infrared panel with wooden frame)
           The NOMATERM unit is put into the spruce wooden frame and from the back side it is protected by the insulation material covered with aluminum foil. The Ecora panels with wooden frame belongs to 2^nd class appliances.
           Installation : Connect panel to supply system through cable box and sufficient cable and fasten infra-red panel directly to the ceiling of the room with screws and plugs (supplied mounting set).

type	size in mm	input (W)	protection
TPS 80	440 x 260 x 40	80	IP 20
TPS 150	840 x 260 x 40	150	IP 20
TPS 200	540 x 540 x 40	200	IP 20
TPS 300	640 x 640 x 40	300	IP 20
TPS 400	900 x 540 x 40	400	IP 20
TPS 500	980 x 640 x 40	500	IP 20
TPS 650	1240 x 640 x 40	650	IP 20
TPS 1000	1840 x 640 x 40	1000	IP 20

2) Type TPS design „K“ ( Ecora panel to be mounted into casette ceiling)
The NOMATERM unit is stick to rear wooden frame and from the back side it is protected by the insulation material covered with aluminum foil. The Ecora panel with wooden frame belongs to 2^nd class appliances.
Installation: Remove tile of tile ceiling. Connect panel to supply system through cable box and sufficient cable. Replace removed tile with Ecora panel TPS design „K“.

type	size in mm	input (W)	protection
TPS 300 kazetový	595 x 595 x 30	300	IP 20

3) Type TPS AL design „J“ or „L“ ( Ecora panels with aluminum frame and ceiling rear holder)
           The NOMATERM unit is put into the aluminum frame and from the back side it is protected by the insulation material covered with aluminum foil. The heating Ecora panels with aluminum frame belongs to 1^st class appliances. Rear holder from zinc-coated plate is a component of this type of infrared panel.
           Standard painting of aluminum frame is white or eloxal coating.
Installation : Fasten rear holder to the ceiling. Connect panels design „J“ or „L“ to supply system through cable box and sufficient cable. Fasten infra-red panel to the holder with springs. There is approximately 8mm airspace between infra-red panel and ceiling for easy dismantling reasons and to align possible ceiling unevenness.

                    Assembly of the Ecora TPS AL panels design „J“ or „L“ is very simple:

type	size in mm	input (W)	protection
TPS 200 AL	510 x 510 x 30	200	IP 20
TPS 300 AL	610 x 610 x 30	300	IP 20
TPS 400 AL	860 x 510 x 30	400	IP 20
TPS 500 AL	950 x 610 x 30	500	IP 20
TPS 650 AL	1210 x 610 x 30	650	IP 20
TPS 1000 AL	1810 x 610 x 30	1000	IP 20

4) Type TPS AL design „T“ ( Ecora panel with aluminum frame to be mounted into plasterboard ceiling)
The NOMATERM unit is put into the „T“ aluminum frame and from the back side it is protected by the insulation material covered with aluminum foil. The Ecora panel with aluminum frame belongs to 1^st class appliances.
Standard painting of „T“ aluminum frame is white.
Installation: cut a hole into plasterboard ceiling. Connect panel to supply system through cable box and sufficient cable. Fasten panel with springs inside of the hole.

type	size in mm	input (W)	protection
TPS 200 AL „T“	525 x 525 x 40 (manhole 507 x 507)	200	IP 20
TPS 300 AL „T“	625 x 625 x 40 (manhole 607 x 607)	300	IP 20
TPS 400 AL „T“	875 x 575 x 40 (manhole 857 x 507)	400	IP 20
TPS 500 AL „T“	965 x 625 x 40 (manhole 947 x 607)	500	IP 20

Assembly of the EcoraTPS AL panel design "T" is very simple:

Guarantee conditions:

Guaranty time is 24 months from sell-by date. Guaranty time is 72 months for the operation of Ecora panels heating element from sell-by date. Product will be free repaired by manufacturer in functional defect incidence not caused by user during guaranty time. Guarantee is not granted to any color changes of workable surface or any mechanical damage caused by misuse.

5) Ecora Bathroom driers (TPK)
The NOMATERM unit is put into the aluminum frame and from the back side it is protected by the insulation material covered with aluminum foil and aluminum plate. The Ecora bathroom drier TPK with aluminum frame belongs to 1^st class appliances. There is inner thermostat built-in TPK to prevent overheating in case that something falls onto heating element. Networking is through cable with contact plug with integrated switch (type „v) or with integrated room thermostat (type „r“)
Standard painting of aluminum frame is eloxal coating.

type	size in mm	input (W)	protection
TPK 200 v	840 x 390	200	IP 44
TPK 200 r	840 x 390	200	IP 44
TPK 400 v	890 x 590	400	IP 44
TPK 400 r	890 x 590	400	IP 44

Guarantee conditions:

Guaranty time for bathroom drier operation is 2 years from sell-by date. Product will be free repaired by manufacturer in functional defect incidence not caused by user during guaranty time. Guarantee is not granted to any color changes of workable surface.